Crawl Space Encapsulation Madison TN

The crawl space has an integral role towards a home’s overall value as well as the living space above. Most homeowners in Madison Nashville  don’t think twice about their crawl space unless they have to make repairs to plumbing, heating ducts or house wiring. While often thought of as no more than a storage area, it also has a tremendous impact on the overall indoor air quality of the entire home.

crawlspace waterproofing

The Best Crawl Space Remediation In Madison TN

By default, the air quality of a crawl space is typically poor. Mold, mildew, radon gas and poor energy efficiency all create several problems. The air that circulates within it eventually makes its way up through the living space. Scientific studies show that up to 50% of living space air originates from the lowest level of the home. With homeowners more concerned about their home’s indoor air quality, the encapsulating of crawl spaces has become a popular solution for such problems.

A damp crawl space creates a safe harbor for harmful molds, in addition to dust mites, termites and other bugs that can infest the home. The presence of excessive moisture will also create a serious problem with the probability for the wooden structure of a home to deteriorate. Crawl space vents pose a further problem. While believed to be a solution to moisture problems, they, unfortunately, make the problem worse. As it turns out, the vents allow cold air and moisture in, which rises into the living area and therefore decreases the heating efficiency of the entire home.

Another all-too-common problem associated with crawl spaces is radon gas. Though it cannot be seen, smelled or tasted, radon is a radioactive gas that can contribute to poor health, including cancer. Radon gas makes its way through the earth, into the crawl space and the home’s living space. According to the U.S.E.P.A., radon gas is the number one leading cause of lung cancer in non-smokers.

Ignoring these various conditions is not recommended for both long-term health and energy usage. Fully encapsulating a crawl space – by both sealing and insulating – is a fully efficient measure in addressing such problems. It makes sense to maintain and improve the lower level area in order to maximize healthy living conditions and home resale value.

While there are several systems for encapsulating, a zero perm liner system that also insulates and reflects heat provides the most benefits. With a proper floor and wall liner, the area will not only be well insulated but will seal out moisture, bug infestation, and radon gas. Other components to look for in a system include a radon gas-dispersing drain fabric, a radon gas ventilation pipe, and a ceiling heat shield.

A complete system with all of the above components will allow any soil gasses – including radon gas – that naturally occur under the liner system, to wick through the drain fabric and escape out through the ventilation pipe. While improved indoor air quality is the primary benefit of a sealed and insulated crawl space, the homeowner will also appreciate a bright, clean, and dry storage area; the ridding of musty smells; less energy usage; and tax credits. Contractors encapsulating crawl spaces will have more to offer to their clients when they can assure the peace of mind with improved indoor air quality.

finished crawl space

Proper Crawl Space Ventilation Can Improve Living Space Air Quality Inside Your Home

Crawl space is one of the most fundamental areas in every home which needs to be kept extremely clean. This is the reason why people go for crawl space encapsulation kits, as these liners make your crawl space extremely clean by keeping away insects, water logging and bad odor. However, the market displays numerous encapsulation kits in different qualities.

Good quality encapsulation kits are more expensive than the cheaper ones, but the cheaper ones are much weaker when it comes to quality. Unfortunately, in my extensive experience in this industry, I have noticed that people are attracted to cheaper ones and choose them for their encapsulation. However, they regret later when the whole thing fails to deliver what it promises.

This undoubtedly is the reason why I suggest using DIY encapsulation kits to save a considerable amount of money. How? It is not only the DIY kit that is expensive, but what's more expensive are the labor charges that come along with it. Labor charges have been increasing higher than ever, and this is the reason why it costs you as much as the encapsulation kits itself. However, if you opt for using DIY encapsulation kit you can save a considerable amount of money that you might spend on labor charges.

Moreover, you can also do your encapsulation at the convenience of your time, patience and energy. You do not have to wait for the professional to arrive at your home, analyze your crawl space and then start the job. Sometimes, this may take longer than you even expect it to finish. This undisputedly becomes the reason why people are more open to taking up DIY kit, as this can finish up their crawl space encapsulation as fast as possible.

What's more? Choosing a DIY kit will help you to ascertain the quality of your liner and the credibility it comes with when protecting your home. By choosing this kit you can take your time and choose the one that suits your preferences and is a permanent solution to your problems. If you leave this to the dealer, you cannot be sure on the quality of liners they will be using and the credibility of their service.

By doing the encapsulation yourself you can be sure that you have done it perfectly and can also alter some changes according to your preference. Hiring a professional will not only take your time and money, but may not be as flexible as you may think.

Crawl space DIY kits are readily available in the market and all you need to do is to research a bit on the types available. Remember, to choose a good quality liner because it all depends on the quality of the liner when it comes to completing the protection of your house.

crawl space conversion

Crawlspace Moisture Control - The Case for Encapsulation

If you get three general contractors together and the topic of discussion turns crawlspaces and moisture control, you will probably hear six opinions. Even the experts seem to have different and often conflicting opinions about what tack is the best to take.

There has been much research on crawlspace encapsulation during the past decade. The US Environmental Protection Agency, the US Department of Energy, the ZEBRAlliance at Oak Ridge National Laboratories, and a non-profit research organization called Advanced Energy have all done excellent and groundbreaking research in the area of crawlspace encapsulation. Their research findings were instrumental in the last revision of the International Building Code. They all agree in a few, very important areas.

When considering your home, think of it as a single system. Your HVAC system, insulation, windows, attic, living space, and crawl space all work together. All of these building components need to be optimized and balanced to achieve maximum comfort, performance and energy efficiency. Your crawlspace is an important part of this system.

Your house is like a giant chimney. By natural convection, air is drawn in through crawlspace vents and air leaks. Because warm air rises, the outside air is drawn through the living space (along with mold spores, odors, and moisture) and exhausted through the attic. In the summer, your crawlspace is naturally cooler than the ambient outside temperature. So when the warm, humid outside air reaches the cooler crawlspace surface areas, the moisture condenses on framing, plumbing, wiring, insulation and especially HVAC ductwork and "sweats", just like an iced tea glass sweats on your kitchen table in the summer. In the southeast it is not unheard of for crawlspace humidity to approach 100% and actually rain inside the crawlspace.

The moisture in your crawlspace creates an ideal environment for wood destroying organisms, mold, and mildew. It can saturate and destroy the effectiveness of your insulation and promote wood rot. And because of the chimney effect, the humid crawlspace air, full of mold and mildew spores, eventually finds its way into your living space creating an unhealthy environment and causing your air conditioning to work overtime to dehumidify the air. Just a vapor barrier might help a bit, but most of the moisture is coming from outside, not your dirt, crawlspace floor.

So, the alternative to a vented crawlspace is an encapsulated (sealed) crawlspace. Crawlspace encapsulation involves sealing all outside vents, installing a high-performance vapor retarder on all exposed wall and floor surfaces at or below grade, insulating the walls and rim joist, and conditioning the air.

The prevailing research claims that by insulating the walls and rim joist, it is unnecessary to insulate the floor. However, if the existing floor insulation is in good condition, leave it in place. We generally recommend a rigid foam board insulation that is fire-retardant, low VOC, and offers an R-13 value or greater. It cuts easily and can be used for sealing existing crawlspace vents too. The sill plate should be caulked and paper-faced fiberglass insulation is used to insulate the rim joist.

The building codes in most areas require the air in an encapsulated crawlspace to be conditioned. That generally means adding a dehumidifier or using the existing HVAC system to condition the air. The EPA and the Department of Energy recommend using the existing HVAC system at a rate of one cubic foot per minute of conditioned air per fifty square feet of crawlspace area. A qualified HVAC contractor can add one or two 4" or 6" vents to a system for a nominal cost. The vents are usually equipped with a butterfly valve that can be adjusted to get the desired air flow.

We prefer using this method since the installation of the vents is generally less expensive than a crawlspace dehumidifier. And since running a dehumidifier is about the same as running a small refrigerator, the cost of conditioning the air with an HVAC system is generally less than running a dehumidifier. Remember that you're not trying to heat and cool your crawlspace; you're just adding a small amount of conditioned air. A relative humidity target of 60% or lower is a good place to start.

When comparing high performance vapor barriers, look at puncture and tear resistance. Other than being absolutely water tight, a high performance vapor barrier should also be flexible, fire resistant, low VOC, and lightweight. There is a world of difference between the 6 mil vapor barrier material sold in most hardware stores and a high performance specialty product. Most reputable suppliers will provide samples.

In addition to dramatically increasing indoor air quality and protecting the structure of your home, several research studies from Advanced Energy indicate that crawlspace encapsulation can actually lower energy usage. These studies were done in several parts of the country with varying climates.


Crawl Space Masters Specializes In Crawl Space Encapsulation in Madison TN.

http://crawlspacemasters.com/nashville/

Wet Crawl Space Madison TN

The crawl space has an integral role towards a home’s overall value as well as the living space above. Most homeowners in Madison Nashville  don’t think twice about their crawl space unless they have to make repairs to plumbing, heating ducts or house wiring. While often thought of as no more than a storage area, it also has a tremendous impact on the overall indoor air quality of the entire home.

crawl space basement

The Best Clean Crawl Space In Madison TN

By default, the air quality of a crawl space is typically poor. Mold, mildew, radon gas and poor energy efficiency all create several problems. The air that circulates within it eventually makes its way up through the living space. Scientific studies show that up to 50% of living space air originates from the lowest level of the home. With homeowners more concerned about their home’s indoor air quality, the encapsulating of crawl spaces has become a popular solution for such problems.

A damp crawl space creates a safe harbor for harmful molds, in addition to dust mites, termites and other bugs that can infest the home. The presence of excessive moisture will also create a serious problem with the probability for the wooden structure of a home to deteriorate. Crawl space vents pose a further problem. While believed to be a solution to moisture problems, they, unfortunately, make the problem worse. As it turns out, the vents allow cold air and moisture in, which rises into the living area and therefore decreases the heating efficiency of the entire home.

Another all-too-common problem associated with crawl spaces is radon gas. Though it cannot be seen, smelled or tasted, radon is a radioactive gas that can contribute to poor health, including cancer. Radon gas makes its way through the earth, into the crawl space and the home’s living space. According to the U.S.E.P.A., radon gas is the number one leading cause of lung cancer in non-smokers.

Ignoring these various conditions is not recommended for both long-term health and energy usage. Fully encapsulating a crawl space – by both sealing and insulating – is a fully efficient measure in addressing such problems. It makes sense to maintain and improve the lower level area in order to maximize healthy living conditions and home resale value.

While there are several systems for encapsulating, a zero perm liner system that also insulates and reflects heat provides the most benefits. With a proper floor and wall liner, the area will not only be well insulated but will seal out moisture, bug infestation, and radon gas. Other components to look for in a system include a radon gas-dispersing drain fabric, a radon gas ventilation pipe, and a ceiling heat shield.

A complete system with all of the above components will allow any soil gasses – including radon gas – that naturally occur under the liner system, to wick through the drain fabric and escape out through the ventilation pipe. While improved indoor air quality is the primary benefit of a sealed and insulated crawl space, the homeowner will also appreciate a bright, clean, and dry storage area; the ridding of musty smells; less energy usage; and tax credits. Contractors encapsulating crawl spaces will have more to offer to their clients when they can assure the peace of mind with improved indoor air quality.

crawl space drainage

Crawl Space Vapor Barrier - A Beginner's Guide On Buying The Right One

Crawl spaces are known for their aesthetic presence-- NOT! When you talk about a crawl space you probably touch upon the dirt floor, the mold buildup, the puddles, the stench, oh and you can't forget about the insulation falling from the ceiling or the dusty old vents.

Unfortunately, this environment can cause a whole lot more damage to the rest of your home than you may think.

The Moisture

Crawl spaces and basements have huge problems with moisture. The stack effect is the proper name for the well-known process of warm air rising, which absolutely has a lot to do with moisture.

When the hot and humid air from the outside enters into the crawl space, the air begins to cool and the warm air pushes and exits through the upper levels. When the hot air cools by even one degree, the relative humidity rises by 2.2 percent.

This is why you find condensation and water buildup on other surfaces! Once this moisture begins to build and the humidity rises in the space mold begins to grow. Mold will continue growing and prospering if it has moisture, organic material to eat and a comfortable temperature. You cannot remove mold by wiping it away, but you remove mold by eliminating the source of moisture.

In other words-- close the vents, seal the space and install a sump pump!

The Vents

As we just learned, air tends to rise within a home. So, when old-school thought encouraged people to install vents, it was unfortunately saying that air would come in through one vent and go out the other vent. This is not the case. Instead, the air comes in through both vents increasing moisture and humidity. In addition, as the crawl spaces conditions worsen due to the vents, the air quality in your home also lessens.

It's been estimated that a third to one half of the air on the first level actually comes from the crawl space, so whatever is growing and prospering beneath your home you can be sure to be breathing in throughout the rest of your home.

In addition, some spaces have fans as well. A fan will only blow the mess around and worsen the problem. Both of these "solutions" also heighten your energy bills and shorten the life of some of your homes heating and cooling appliances. Your air conditioning will be working a whole lot harder to cool and your heating system will be working very hard to keep your home warm. Unfortunately, the vents and fans in your crawl space are a big factor in your energy waste and increase in expenses.

The Solution

Since crawl spaces have problems with moisture control and mold growth the best solution will close-off air flow from the outside and prevent moisture from entering through the soil, cracks and vents. In addition, the solution must prevent mold growth and include a water drainage system for when leaks occur and water somehow makes its way into the space.

This solution is to install the CleanSpace Crawl Space Encapsulation System, which will enclose the entire crawl space with a vapor barrier that also separates the space from the soil foundation. In addition, you can close-off the vents and include a sump pump drainage system.

No more vents, no more fans equals better air quality and a cleaner environment.

finished crawl space

10 Reasons to Encapsulate Your Crawl Space

The single best thing you can do to eliminate moisture and odors coming from the crawlspace is to apply a heavy sheet of plastic. Plastic wrap comes in clear or black and in different thicknesses. Purchase either color and with a thickness of at least 6 mil or better yet 10 mil.

Roll out the plastic so that all of the crawlspace floor is completely covered with plastic. When you have to cut the plastic to go around something, be sure to cover the cut with additional plastic or lap the original layer over the cut out. It's OK to use duck tape on the plastic vapor barrier as well. Just be sure to not have any voids in the plastic where moisture and odors can still get through.

The walls of the crawlspace should be covered as well to better eliminate moisture concerns as they can harbor condensation, a major source of moisture issues. Just roll out extra length of plastic so that you can run it up the crawlspace wall and using the stapler, tack along the ledger board located just above the concrete block or poured wall.

If you eliminate odors, moisture from the crawlspace and other undesirable elements coming from the ground beneath your home, your family will be living in a much healthier environment.

Although this task can be accomplished by yourself, it will be much easier if you can get a buddy or helper to go into your crawlspace and aid in the rolling out of the plastic barrier.

6 mil plastic is fine, however, if you can find thicker plastic (greater than 6 mil) then it will be much harder to rip or tear as you move along the crawlspace.


Crawl Space Masters Specializes In Crawl Space Encapsulation in Madison TN.

http://crawlspacemasters.com/nashville/