crawl space water Cleveland, Tennessee

The crawl space has an integral role towards a home’s overall value as well as the living space above. Most homeowners in Cleveland Tennessee  don’t think twice about their crawl space unless they have to make repairs to plumbing, heating ducts or house wiring. While often thought of as no more than a storage area, it also has a tremendous impact on the overall indoor air quality of the entire home.

dry crawl space

The Best basement waterproofing In Cleveland TN

By default, the air quality of a crawl space is typically poor. Mold, mildew, radon gas and poor energy efficiency all create several problems. The air that circulates within it eventually makes its way up through the living space. Scientific studies show that up to 50% of living space air originates from the lowest level of the home. With homeowners more concerned about their home’s indoor air quality, the encapsulating of crawl spaces has become a popular solution for such problems.

A damp crawl space creates a safe harbor for harmful molds, in addition to dust mites, termites and other bugs that can infest the home. The presence of excessive moisture will also create a serious problem with the probability for the wooden structure of a home to deteriorate. Crawl space vents pose a further problem. While believed to be a solution to moisture problems, they, unfortunately, make the problem worse. As it turns out, the vents allow cold air and moisture in, which rises into the living area and therefore decreases the heating efficiency of the entire home.

Another all-too-common problem associated with crawl spaces is radon gas. Though it cannot be seen, smelled or tasted, radon is a radioactive gas that can contribute to poor health, including cancer. Radon gas makes its way through the earth, into the crawl space and the home’s living space. According to the U.S.E.P.A., radon gas is the number one leading cause of lung cancer in non-smokers.

Ignoring these various conditions is not recommended for both long-term health and energy usage. Fully encapsulating a crawl space – by both sealing and insulating – is a fully efficient measure in addressing such problems. It makes sense to maintain and improve the lower level area in order to maximize healthy living conditions and home resale value.

While there are several systems for encapsulating, a zero perm liner system that also insulates and reflects heat provides the most benefits. With a proper floor and wall liner, the area will not only be well insulated but will seal out moisture, bug infestation, and radon gas. Other components to look for in a system include a radon gas-dispersing drain fabric, a radon gas ventilation pipe, and a ceiling heat shield.

A complete system with all of the above components will allow any soil gasses – including radon gas – that naturally occur under the liner system, to wick through the drain fabric and escape out through the ventilation pipe. While improved indoor air quality is the primary benefit of a sealed and insulated crawl space, the homeowner will also appreciate a bright, clean, and dry storage area; the ridding of musty smells; less energy usage; and tax credits. Contractors encapsulating crawl spaces will have more to offer to their clients when they can assure the peace of mind with improved indoor air quality.

finished crawl space

Thinking Long-Term Safety & Health With Proper Foundation Structural Repair & Basement Waterproofing

A crawl space dig out is the process of turning your crawl space into a basement. This vastly increases storage space and can, in some cases, increase living space as well.

But, a crawl space dig out can be an enormous and daunting task. And, if done improperly, it can be dangerous. If you don't want to have a professional do it for you, please follow the steps below.

To get started, find place in the outside wall of your crawl space that you can safely enter the new basement with a temporary or permanent set of steps. Make sure the wall opening is big enough to handle at least a 36-inch door, preferably making the area for the steps at least 48-inches wide.

Warning:

If your soil is sandy or gravel and or may be full of water at least part of the year do not consider this procedure, it is very dangerous and you may damage or lose your house.

Make sure that prior to digging the hole for the outside exit, please build a header of sufficient size to hold the floor of the home where you will be removing the old foundation.

You need to excavate to a depth that will accommodate a four-inch concrete slab and still have at least 7-foot, 6-inches of clearance under your floor joist. It is entirely possible that you will have 48 inches of soil to remove.

When digging out a crawl space, you can not excavate any closer than 24 inches away from the existing foundation.

You can remove the soil sufficiently to work along the wall without removing the entire area you wish to change.

When you get the soil out to a depth that you prefer, pour a footer that is eight inches thick and 16 inches wide. The footer should be below the bottom of the new slab so it is a good idea to dig the area for the footer below the level you remove for the floor area. This is a very important step in a crawl space dig out.

Then, when your block is level with bottom of the old foundation wall you need to pour a four-inch thick slab of concrete on top of the wall and over to the outside existing wall.

Prior to pouring your "Cap" you must fill between the block and soil that is under the old foundation with fill sand or "Pea-gravel." Assuming that you probably have some kind of support under the center section of the floor system, you will have to provide support for the beam that is presently supporting the floor while excavate for a new footer for a steel post that will hold the floor of your new space.

Make sure your footer for this part of the project is about eight inches thick & 24 inches square.

You will need to level the floor area for your new slab and install four inches of perforated plastic pipe draining to a sub pit with an automatic sub pump that dispenses the water to the outside at least five to ten feet away from the foundation of the home. I'd suggest using "Pea-gravel" for fill under the slab but you can you fill sand also.

Now, build your stairs to the outside in a similar fashion but you need to cover it with a steel "pre-fab" unit such as a "BILCO."

If you do this correctly and maintain it, it will last for many, many years. It is strongly suggested you get a professional to do this job or at least help with it because mistakes can be dangerous and very costly.

digging out a crawl space

Crawl Space Encapsulation Systems DIY

Many homeowners try to cut costs and increase their home's comfort level by installing a crawl space vapor barrier. This will instantly make your home healthier for you and your family, and prevent moisture damage, mold, mildew, foul smells and odors.

Most homeowners tend to look at their crawl space as separate space from their home, but in reality, the two are one. Water vapors that surface from the ground are continuously entering, creating undesirable conditions for you, your family, and your home.

Purpose

The purpose of a crawl space vapor barrier is to stop moisture and wetness from entering and affecting the floor and walls of your basement. Moisture tends to flow from warmer to colder spaces.

Many homeowners don't realize the importance of the proper installation, in order to keep moisture and water vapors from getting in the walls and floor of your basement-- condensation can lead to expensive structural damage. Also, if you can help control the moisture and dampness, you can greatly reduce the amount of energy required to cool and heat your home.

Preparation

When considering the installation of a vapor barrier, take into consideration two spaces in your home; the crawl space and the attic. Humidity tends to build in the walls of both these areas causing mold, mildew and dry rot. This can cause severe health issues for adults and children, especially for those with asthma, breathing difficulties, and allergies. In addition, it can cause severe structural damage to your home.

Some homeowners think that because they insulate the floor joists there is no need to do any additional work, but these items do not serve the same purpose!

Tips for Installation

One of the most popular do-it-yourself vapor barrier products is polyethylene, or plastic sheeting. This plastic sheeting comes in various thicknesses; 4mm, 6mm and 10mm.

With today's technology, this product is made from a high quality material, resistant to rips and punctures. Always check the soil so there aren't any objects or materials that may damage the lining. The slightest puncture, rip or tear could compromise the entire system.

Always, make sure the space is dry before you begin any repairs. To remove the moisture, you may need a dehumidifier.

Overlap the barrier a minimum of 12 inches on the side walls. Be sure it is tight. Use furring strips and masonry nails to firmly secure the lining then caulk along the joints.

Seal all the seams with a heavy duty tape. However, it is recommended not to use tapes that are not specially designed for sealing vapor barriers. When working in the basement you will be forced to contend with pipes, make the proper cuts and seal securely with tape.

The completion of your crawl space vapor barrier will be the best investment you can make in your home.


Crawl Space Masters Specializes In Crawl Space Encapsulation in Cleveland TN.

http://crawlspacemasters.com/tennessee/